Whether you are building a concrete slab for a home or paving a driveway, paving concrete must be done with care so it will harden evenly. For large projects, using concrete pumping is an effective method. Below is a step-by-step guide on how to properly pave concrete evenly with concrete pumping.

1. Once you have chosen the site for your project, you must check the quality of the soil. Soft soil will require a gravel rock bedding to prevent the cement slab from sinking into the ground once it has been poured and hardens. It is important that your site is level and can withstand heavy concrete.

2. Measure the size of the area and put in markers around the site to mark off the location of the concrete pour. Dig out the site and make sure it is flat and level throughout. Add the gravel to the site and smooth it with a rock rake so that the entire area is even. A gravel rock bedding of a few inches should be adequate to properly secure the area that you will pour the concrete. Make sure the gravel is graded so that the concrete will be the same thickness throughout the site. You may want to make the edges of the site thicker to prevent cracking due to changes in the temperature.

3. Install the forms for your site which will support the concrete as you pour it. This is normally either 1×4 or 2×4 lumber that is held in position by wooden stakes. You will have to drive the stakes into the ground in order to properly secure the form boards and keep them aligned. Once the form is installed, lay a mat of steel reinforcing bars across the site for added reinforcement of the concrete. You can buy reinforcing wire mesh at any building supply store.

4. Pouring the concrete can be done by a concrete pour truck. You will need the proper tools to smooth it as it is being poured. You want to keep smoothing it as it is poured so it comes out even and smooth. A screed and a 2×4 lumber are good tools for smoothing it. You just have to drag it across the concrete leaving a somewhat rough texture on the surface. After it is dry, you will then need to apply a concrete cure to keep it from drying to quickly. The concrete slab should also be protected from moisture while it is drying.

5. Once the concrete is dry, you should apply a concrete finish to make sure the site is completely flat and even. Once this is done, remove the forms and fix any damage that may have occurred to the ground around the project site.

Paving concrete using concrete pumping is an efficient and cost effective way of pouring concrete. For large projects, one will save a lot of time using this method of concrete pour. When done correctly, paving concrete with concrete pumping will make any project less difficult and the result will be a high quality and even concrete pour.

Oahu Concrete Pumping

Concrete is not new on the construction and Pumping scene. Evidence has been found that it was actually used during the Roman Empire days although in a different form. Portland cement, which is the basis of cement products, was patented in 1824 by an Englishman named Joseph Aspdin. Concrete is used throughout the country, as well as the rest of the world, for pavements, Pumping and many other things. To keep concrete Pumping installed or in good condition one needs Concrete Pumping Equipment for Industrial Services.

When used in Industrial Services concrete must be a stronger and more durable than that used in some other types of projects. Using pure water and blending in other components, such as aggregates and admixtures, with the original mix is paramount to achieving this end. When this is done the resulting product will have superior, industrial strength. For this reason special concrete equipment is needed when new installation or repairs are made. This is especially important when working on industrial Pumping.

When working with industrial services, the person in charge of the project must carefully select equipment that will not only be the correct size, but have the strength required for the job. If on a repair job, such as a pipe blockage, one of the most important things to have is a micro inspection camera. This camera is invaluable for inspecting underground pipes to determine what type of blockage is occurring.

Having located the blockage in the pipe a course of action must be taken. Will the pipe have to be dug up and replaced? Will a concrete floor have to be broken up and replaced? This is time consuming as well as a costly project and should be avoided if at all possible. When the problem has been determined, having the correct equipment at hand is imperative to do a complete job in as little time as possible.

In working with concrete Pumping on an industrial job or any other concrete projects, there are the usual, every day tools needed. Things such as sledges, pry bars, trowels, mixers, floor scrapers and many others have to be a part of basic equipment. If it is a huge project, truck mounted boom sprayers might be needed. If it is a smaller project in a confined area, using the smaller trailer pumps might be a better choice. The large, truck mounted boom can output approximately 200 yards per hour.

The many types of equipment used in industrial concrete Pumping work are lengthy. There is a different type of equipment needed for every job depending on the severity of the problem as well as the overall area to be covered. Determining a problem under a concrete warehouse floor for example, might involve tearing up a great deal of flooring and replacing it.

The very best type of equipment which is now on the market ensures the company or person working on concrete Pumping in an industrial atmosphere outstanding quality in the products utilized. Through years of testing, manufacturers have now developed products that make cutting through concrete as easy as cutting a cake. In addition, safety precautions are designed into each piece of equipment to protect the workers.

When searching for Concrete Pumping Equipment for Industrial Services on Oahu, it is important to purchase only the best available. The higher quality equipment is manufactured using only the best steel products. Purchasing this type of equipment assures the buyer will not have to spend a lot of money repairing or replacing equipment needed to complete the job.

Ohana Concrete Pumping has the state of the art equipment that is demanded on Oahu.

We are a family owned business. We are committed in getting our trucks to your job on time. We know that time is money and that having the best equipment on site and ready is the only way to do business. We operate and maintain our equipment to the top standards in the industry.